Lincoln Corsair is a reliable road companion, but its a machine with hundreds of interconnected parts, and like any other machine it sometimes fail to deliver normal operation. In this article we go through most common causes of Corsair breakdown and how you can fix the problem.
The most common causes that hinders normal starting operation of your Lincoln Corsair are dead key fob battery, dead 12v battery, corrosion on battery terminals, bad alternator, clogged fuel filter, broken starter, blown fuse, empty gas tank, immobilizer error or any fault in the electrical system.
1. Weak Battery
If your Corsair’s engine won’t crank or cranks very slowly, then the most likely culprit is weak or dead 12v battery. Investigating more closely and doing a battery voltage test will clarify whether the starting problem is due to the battery. A test can be done to measure the voltage between the battery poles, check the acid level and assess the condition of the starter battery.
If a new car battery has been installed, the battery may not have yet reached its full capacity. There is nothing to worry about. A new battery only develops its full capacity over time.
Test 12v battery
The voltage of the battery on your Lincoln Corsair can be measured precisely with a multimeter. Before the test, the multimeter is set to the voltage range of the battery and connected to its plus and minus poles. Successful testing of the car battery, i.e. checking the voltage, usually results in values of approx. 12 to 13 volts. Values above 14 or below 11.5 volts require an expert assessment of the condition of the car battery. Because the battery may have a defect with these measured values and must be replaced.
Jump start Lincoln Corsair
If dead battery is the reason for the breakdown of your Corsair, you can easily jump start it using jumper cables and a healthy battery from another vehicle, or using a battery booster if available.
First connect red cable to the positive terminal of your Corsair’s dead battery, then to the positive terminal of donor battery. Next connect black cable to the negative terminal of donor battery, then to the bare metal in the engine bay of your Corsair. Start the donor vehicle and then your Corsair. Remove the cables in reverse order.
2. Corrosion on battery
Corrosion on the contacts of your car battery leads to loss of contact and reduced current flow, which means that your engine can no longer start properly.
To know if your Corsair’s starting problems are from dirty battery contacts, you need to investigate them. If you lift the rubber covers over the two battery terminals, you can check the terminals for corrosion. If you discover white deposits or silvery-green deposits, but no further cracks or damage, you do not have to replace the battery, just clean it.
Clean battery corrosion
To clean the battery on your Lincoln Corsair, you have to remove the pole cables first, which requires no special knowledge, just a little concentration, as the order is very important. First remove the black cable from the negative pole. If the pole clamp is very tight, you can open it with pliers. We advise against using metal pliers, but if you use them, you must make sure that you do not touch any other parts of the body. Next you can unplug the red positive pole cable. Once the battery has been removed from the circuit, you can start cleaning the corroded battery. After cleaning, reconnect the terminals.
3. Weak key fob battery
If your Corsair has push start/stop button, then its possible that your vehicle may not start due to weak key fob battery. Don’t worry, you can still start your vehicle – the battery is only used to send the signal for locking/unlocking. If the key fob battery is empty, the door no longer locks or unlocks at the push of a button. The doors must then be opened manually. The immobilizer is controlled by a passive transponder. Passive means, among other things, that the transponder in the key does not need its own power source.
How to start Lincoln Corsair with dead key fob battery
If you have a model of Corsair which only has a key fob with start/stop button and no place to insert a key, then try placing your key fob as close to the start/stop button as you can and then start the vehicle. If it doesn’t work, then look in your vehicle’s operational manual for exact location of key fob placement, as it may vary depending on model.
Tip: You can try starting your Corsair with its second key. It will also rule out any other problem with the first key, for example, water damage.
4. Broken starter motor
A starter is a motor for starting the engine of your Corsair. The average life of a starter motor is about 100,000 to 150,000 miles, and the life will be shortened if the engine is started more frequently. In any case, since the starter motor also has a limited life, it will break down after using the car for a long time, and if the starter motor breaks down, the engine will not start.
Symptom: When you turn the key to start the engine of your Corsair, you will hear a clicking sound, which is the sound of a bad starter motor. And if the starter motor does not work with a healthy battery, suspect a malfunction of the starter.
If the starter fails, it usually needs to be replaced with a new one.
Temporary fix for starter
If the engine does not start due to the starter, the engine may start if you turn the key while hitting the starter motor with something like a stick or metal tool. This workaround is effective when the parts inside the starter are stuck together or the gears are slightly out of alignment.
However, it is possible that the starter is nearing the end of its life, so it is recommended that you have it inspected at a dealer or maintenance shop.
5. Defective alternator
An alternator is a generator that produces electricity. If your Corsair’s alternator fails, it will not be able to produce electricity and the battery will not be able to charge. Therefore, even if you think that the cause of the engine not starting is a battery failure and replace the battery, the battery will soon run out and the engine will not start.
Alternators rarely break down. In particular, modern cars have improved performance, so it is said that they will last 200,000 to 300,000 miles. Still, it can break down depending on how you use it, and in the case of a used car, the alternator may be quite old. Don’t let your guard down.
If the alternator breaks down, it must be replaced with a new alternator.
6. Clogged fuel filter
The fuel filter of your Corsair does not wear out like a mechanical part, but it gets clogged by dirt and airborne particles and clogs over time. The permeability of the filter drops, and so does the fuel pressure. To a certain extent this doesn’t matter, but if the fuel filter is too dirty, the engine will no longer perform at full capacity and in some instance may not start at all. Cleaning is not possible, you can only change the filter.
7. Fuel pump failure
If your Corsair’s fuel pump fails, then the engine won’t start. The pump normally ensures that the necessary amount of fuel is passed from the tank to the injection system of the engine with sufficient pressure.
Before your fuel pump stops working, it usually becomes noticeable: if your car’s engine breaks down from time to time, the car is difficult to start, the engine jerks a little or the engine performance drops, you should have your pump checked.
Wear or contamination of the pump can be the reason for this. If the pump is leaking, a power contact is broken, a line or a pump lever is broken, the fuel pump is usually also noticeable before failure. You can have a defective fuel pump replaced in your workshop.
8. Blown fuse
In rare cases, a blown fuse could also be the culprit in the breakdown of your Corsair. Check all fuses in the fuse box essential for starting the engine. But, be careful when lending a hand yourself to the fuse box! The box is under power and repairs or tests should always be done in a workshop.
9. Defective spark plugs
Without functioning spark plugs, the engine will not start. The spark plugs themselves are often not affected by a defect. Instead, plug connections on the ignition system come loose. If only one plug is actually loose, you can fix the problem yourself on site. If a spark plug has failed, it must be replaced in the workshop.
10. Rodent damage
Rodent damage can be another reason why your Lincoln Corsair won’t start. The animals crawl under the vehicle and bite through cables and wires. In principle, this can affect all vehicle systems such as the fuel supply, the oil supply or the power supply.
The rodent damage can usually be seen quickly by looking into the engine compartment. The damage caused by the rodent bite can be repaired in the workshop. Be prepared for relatively high costs here.
11. Engine failure
Although very rare, but it can also be the cause of the breakdown of your Corsair. If a vehicle has an engine failure, then nothing works anymore. It is not uncommon for the driver of a vehicle to be responsible for such damage. Typical causes include tearing of the timing belt, incorrect fueling, insufficient oil, hydrolock, overheating of the engine, or continuous driving in an excessive speed range.
Only an experienced mechanic can diagnose engine failure in a workshop.
Use OBD2 scanner for diagnosis
Since Lincoln Corsair is equipped with on-board diagnostics (OBD), a fault diagnosis can provide initial indications of where the malfunction is located.
To begin troubleshooting, you must first connect the diagnostic tool to your Corsair. The OBDII connector is usually located under the dashboard. With the wire connected, you should turn the ignition on. But be careful not to start the engine. Most diagnostic devices then ask for some information about the vehicle. It is important that you enter this 100% correctly, otherwise the result of the search may be falsified. In addition to the vehicle manufacturer and model, you usually also have to type in the engine and vehicle ID number. For exact troubleshooting, always check whether the information is correct.
There are many reasons why your Corsair may not start. When looking for the trigger, you should always start with the most obvious cause, the empty battery.
In any case, it is advisable for laypersons to call a breakdown service or a workshop. In the event of a defect, the latter can directly initiate the repair.